All the electronic module products in this store are developed and produced by our store, which is definitely the direct selling price of the factory! The circuit board is printed with LOGO, only this one, no semicolon, please look for the cloud particle electronics!!

ExplainWith regard to the use of products, please look carefully at first, we introduce instructions, do not know where to leave messages to us directly.Before the baby issues, the technicians will electrify and test properly before they send out!After receiving the baby, please look at the wiring method, and then power test, and then solder, because of their own wrong line, misoperation or DIY changes are not warranty Oh!

Calibration method:The module has a calibration function, so you don't have to worry about measuring inaccuracy. If you find that the display is not correct, you can calibrate it by the following methods. Just use it for the first time! Received baby suggested the following method for a calibration!

Voltage calibration:Power is turned off, press the "Settings" button, enter the power, voltage calibration mode, the LCD screen began flashing, release the keys, click "Settings" button to add, "OK" to reduce the input voltage, the calibration is correct, such as: the input voltage is 12.65V, voltage adjustment will be at that time 12.65V, automatically save 2 seconds after the power out is complete calibration!

Module parameter

Input voltage: 10-32V DC input

Output voltage: 11-60V DC continuous adjustable (recommended working voltage remaining margin, not more than 55V,Only applies to the input voltage is less than the output voltage of the application, can not step-down)

Output current: the maximum 8A is over 4A. Please strengthen the heat dissipationFans are sold here!It is related to the pressure difference between input and output, the greater the pressure difference, the smaller the output current

Output power:Natural heat dissipation, maximum 90W, enhanced heat dissipation, maximum 150W

Module property: non isolated boost module (BOOST)

Output constant current range: 0.3-8A

Operating temperature: -10~+85 degree (ambient temperature is too high, please strengthen the heat dissipation)

Operating frequency: 150KHz

Conversion efficiency: up to 95% (efficiency is related to input, output voltage, current, pressure difference)

Short circuit protection: no (please do not use short circuit)

Input reverse protection: No, please add anti diode at the input. This is on sale!

Output indicator: with charging instructions, charging yellow, full of blue

Output counter backflow: Yes

Installation method:Both sides of acrylic board, on 8 Pillars, 8 3mm screws,Installation is easier when you install the button!

Back of module:

Module side:

 

The outer shell of the module shell is provided with an opening of the fan, and can be used for increasing the cooling of the fan, and the fan is sold in the shop! The fan needs another shot!

Setting instructions:

Set the key to set the display mode, divided into three kinds:

1, F-0 mode: display output voltage;

2, F-1 mode: display input voltage;

3, F-2 mode: alternate display input and output voltage;

Directions: press the settings button, the cycle shows three display modes, and the corresponding indicator light is on or off,Press OK to save and exit,Press the OK button individually to switch the LCD screen back light.

 

 

 

Usage method

Regulating voltage:Under no load conditions, adjust the constant voltage potentiometer ADJ-V, so that the output voltage to the voltage you want;

Regulating current:The load adjusting potentiometer ADJ-I constant current, so that the output current of the constant current value you want (the default is 2A, if the constant current value is small, the counterclockwise adjusted number of laps will have to change, if not adjusted) constant current can not adjust current needs;Attention: please don't adjust the current by short circuit. The circuit structure of the boost module can not be adjusted by short circuit!

Special attention:Constant current adjustable current, must be the actual output load current is greater than the set current will be a constant current mode, or a constant pressure of work, not to the current 2A, is connected to any device 2A, also hope to know.

Light transfer instructions:Charging lamp current factory default is 0.1 times of the charging current; (the battery during charging current is reduced gradually, gradually from the constant current charging to constant voltage charging, if the charging current is set to 1A, then when the charging current is less than 0.1A, the charge indicator lamp is light yellow, blue lights, when the battery is fully charged;