Hot Sale XGecu PRO T56 Universal Programmer +51 Adapters 24/25/26/93 Serial EEPROM, 27/28/29/36/37/39/49/50 EPROM
Hot Sale XGecu PRO T56 Universal Programmer +51 Adapters 24/25/26/93 serial EEPROM, 27/28/29/36/37/39/49/50 EPROM
SIZE: 12.9cm x 8.5cm x 2.9cm
Super performance Super speed Super small portable
Cool appearance Low power consumption Super stability
(1). 32-bit MCU 200MHZ + Xilinx SP6 FPGA structure, USB2.0 HS 480MHZ transmission
(2). 56 pin full drive IO design. All pins have a maximum operating frequency of 50MHZ and high reliability.
(3). Stable and reliable 8Pins in-circuit programming interface, the wire Lehgth is more than 30CM,
and it can communicate reliably at 25MHZ.
25 series / EMMC in-circuit programming with a maximum clock frequency of 40MHZ-50MHZ
(4). VCC voltage 1.2-6.5V 64 levels adjustable,
VPP voltage 6.5-25V 64 levels adjustable.
IO communication signal voltage continuously adjustable 1.2V-3.6V
VCC 120MA-320MA overcurrent protection continuously adjustable
VPP 120MA overcurrent protection.
(5). Power consumption: 5V <500MA. All chips do not need external power supply.
It can be connected to an external power supply 5V-5.5V 500MA for multipile programming.
The external power can be powered by a cell phone charger can be seen everywhere.
The programmer has multiple protections for the external power supply:
overvoltage protection / reverse connection protection / overcurrent protection / low voltage prompt.
(6). Write EMMC Speed: 12MB/s-25MB/s
Reading EMMC speed: 14MB/s-45MB/s is 2-5 times faster than similar programmers.
(This is important for large-capacity chips, 64GB EMMC chips,
If 10MB/s (the average programmer cannot reach 10MB/s) reading takes 6400 seconds,
T56 can usually reach more than 20MB/s, as long as about 3000 seconds)
Ability to handle extremely high speeds, meaning that programmer hardware has greater stability at lower speeds
(7). Open self-test function, self-check each VPP/VCC /GND/IO
3. 56 Pins FULL DRIVE
|
8. EMMC programming function special introduction (1). The most functions EMMC programmer, which can perform one-key mass production operation on EMMC (also can be programmed with 4 machines in one computer) Load project files, load all parameter settings at once, and directly program. Read and write speeds up to 12MB / s-45MB / s (2). EMMC function introduction 2.1: Analysis function : analyze the content of the original chip, and display the following results: Display chip manufacturing information Visual display of chip usage up to 8 partitions Each partition shows whether it is write protected, can be read, can be rewritten or deleted Shows whether the entire chip is temporarily or permanently write protected Show whether the chip is password protected Show whether the chip uses a 32-bit security authentication code to write to the RPMB. Show other important parameters of ECSD/CSD/CID You can also read the ECSD / CSD / CID file into this programmer to enter the load analysis Can also perform some general analysis on ECSD files read by other programs 2.2: Read/write functions (all functions can be completed with one-key) Read CID / CSD / ECSD. Clear full-chip temporary write protection before programming Clear temporary write protection groups before programming Delete chip before programming Blank Check the chip before programming Programming 32-bit authentication key Perform chip password verification Partiton Config Read and Programming to BOOT1 Read and Programming to BOOT2 Read and Programming to RPMB Read and Programming to GP1 Read and Programming to GP2 Read and Programming to GP3 Read and Programming to GP4 Read and Programming user data (User Area) Setting temporary write protection groups Setting permanent write protection groups Setting password (or reset password) Programming ECSD Programming CSD Automatically verify all the above operations after Programming (3) .ISP in-circuit programming function 3.1 Ultra-high stability ISP in-circuit programming, wire length can be up to 25CM, working frequency 25MHZ, reliable work, If the length is within 10CM, it can be operated at 40-50MHZ. 3.2 ISP can also use 4-bit mode, the operation speed is increased to 4 times (4) .EMMC other functions 1. The working frequency and working voltage of EMMC can be adjusted manually. 2. The user area data can be read and written in multiple files. 3. If there is a password when Erase, will do Force Erase 4. Password can use ordinary password or SHA1 encrypted password 5. The value of ECSD / CSD can be loaded from the ECSD_CSD file or manually set by the user 6. Ignore data CRC error during read operation 7. Optional automatic verification after reading operation is completed. 8. The device information includes high-definition pin map and ISP wiring 9. EMMC has real-time speed display during read and write operations, and the final average speed display (5).EMMC Adapter and ISP connection
9. High-speed programming of Parallel NOR Flash 28/29 series
Packing List: 1 * XGecu T56 universal programmer 1 * TSOP56/48/40/32 Adapter 1 * ADP-SSO-056-0.8 Adapter 1 * TSOP48 Adapter 1 * SOP44-DIP44 1.27mm (530mil) Adapter 1 * SOP28-DIP28 (300mil) Adapter 1 * SOP20-DIP20 (300mil) Adapter 1 * SOP16-DIP16 (300mil) Adapter 1 * Double SOP8-DIP16 CNV-SOP20 (208mil) Adapter 1 * SOP8-DIP8 CNV-SOP20 (208mil) Adapter 1 * SOP20-DIP20 CNV-SOP20 (208mil) Adapter 1 * SOP8-DIP8 CNV-SOP-DIP16 (150mil) Adapter 1 * SOP16-DIP16 CNV-SOP-DIP16 (150mil) Adapter 1 * PLCC44-DIP44 1 * PLCC44-DIP40 1 * PLCC32-DIP32 1 * PLCC28-DIP28 1 * PLCC28-DIP24 1 * PLCC20-DIP20 1 * SSOP28 to DIP28 1 * TSSOP8 to DIP8 1 * KB9012 board 1 * SOP8 IC Clip 1 * ITE 29/39/49/50 series 32/40/48 feet adapter 1 * Multipurpose ISP-DuPont-Header Adapter 1 * EC NPEC288 NPEC388 PCB Board 1 * TSOP28Pin 0.65mm Adapter Board 1 * SOP28Pin 1.27mm Adapter Board 1 * TSOP20Pin 0.65mm Adapter Board 1 * SOP20Pin 1.27mm Adapter Board 1 * TSOP16Pin 0.65mm Adapter Board 1 * SOP16Pin 1.27mm Adapter Board 1 * TSOP14Pin 0.65mm Adapter Board 1 * SOP14Pin 1.27mm Adapter Board 1 * TSOP10Pin 0.65mm Adapter Board 1 * SOP10Pin 1.27mm Adapter Board 1 * TSOP8Pin 0.65mm Adapter Board 1 * SOP8Pin 1.27mm Adapter Board 1 * QFN8-DIP8 Programador Adapter WSON8-DIP8 8x6mm 6x5mm 1 * SOP8/MSOP8/SSOP8/SOP16-DIP16 simple Adapter 1 * Adapter SOP8-DIP8 simples 1 * 1.8V Conversion Block 25 series low voltage chip adapter 1 * ICSP Cable 1 * LCD LED screen EDID Cable 1 * IC Chip Extractor 1 * Suction Pen 1 * USB Cable 1 * VGA Cable 1 * Anti-Static Wristband Wrist Strap Band ESD Discharge PC Electricity GroundingABOUT US
|
|
We still deal in Laptop accessories,include VGA Card, LCD screen, CPU, keyboard, Battery, Adapter,e-ink, DC Jack, BGA balls, BGA stencil, Soldering tin wire and so on.
About shipping
We ship wordwide by EMS,DHL,UPS,FedEx,TNT,China Poset,E- packet,SingaporePost,HongKong Post and so on. We are unable to control the delivery time becaunse it is processed by Third-party service, but if the parcel has not arrive within expected time,please contact us,we will help you to track it and give you a satisfied reply.
Our advantage
Within 12 Hours quickly reply. Most stock and quickly delivery 100% Quality guarantee on all products in stock Knowledgeable and experienced sales staff. Our sales representative will be here always serve for you.
About feedback
If you are unhappy with our service or any other problem, please contact us before opening dispute or leaving feedback and we will resolve the issue immediately, thank you!
|
Brand Name : LRF
Operating Temperature : T56 USB programmer
Type : Logic ICs
Dissipation Power : T56 Universal Programmer
Model Number : XGecu T56 Pro Programmer
Supply Voltage : XGecu
Application : Computer
Origin : Mainland China
Package : SMD
Condition : New
shipping : free shipping
Place of Origin : Guangdong, China (Mainland)
Quality : Original factory brand new quality
Advantage : Factory Price & Plenty In Stock & Fast Dispatching
Package : yes
Warranty : 60 days from receipt
is_customized : Yes
Condition : new
Model : XGecu Pro T56 Programmer