Night Light DIY Kit DC 9-12V Infrared Remote Control Lamp White LED Light Dual Gears Brightness Adjustable Nightlight Electronics Suite

1.Introduction:RCN-1 is a DC 9V-12V Infrared Remote Control DIY Kit. User can use any infrared remote controller to control the lamp on or off with 18pcs white LED.2.Feature:1>.18pcs highlight LED2>.Perfect simple circuit3>.Two position brightness control4>.DIY hand soldering5>.Infrared Remote Control3.Parameter:1>.Product Name:RCN-1 IR Control Lamp DIY Kit2>.Product Number:RCN-13>.Work Voltage:DC 9V-12V4>.Work Current:30mA5>.Power Type:5.5mm Power Socket or 9V Battery(Not Included!)6>.Work Mode:Switch or Infrared Remote Control7>.Color:White LED8>.Work Temperature:-40℃~85℃9>.Work Humidity:5%~85%RH10>.Size(Installed):65*65*36mm4.Function:1>.S1 black button is used to turn ON or OFF lamp.2>.S2 self-locking switch is used to change led brightness. 12pcs LED turn ON or 18pcs LED turn ON.3>.Any infrared remote controller to control the lamp on or off.5.Application:1>.Training welding skills2>.Student school3>.DIY production4>.Project Design5>.Electronic competition6>.Gift giving7>.Crafts collection8>.Home decoration9>.Souvenir collection10>.Graduation design11>.Holiday gifts6.Installation Tips:1>.User needs to prepare the welding tool at first.2>.Please be patient until the installation is complete.3>.The package is DIY kit.It need finish install by user.4>.The soldering iron can't touch the components for a long time(1.0 second), otherwise it will damage the components.5>.Pay attention to the positive and negative of the components.6>.Strictly prohibit short circuit.7>.User must install the LED according to the specified rules.Otherwise some LED will not light.8>.Install complex components preferentially.9>.Make sure all components are in right direction and right place.10>.Check that all of the LED can be illuminated.11>.It is strongly recommended to read the installation manual before starting installation!!!12>.Please wear anti-static gloves or anti-static wristbands when installing electronic components.7.Installation Steps(Please be patient install!!!):1>.Step 1: Install 4pcs 330ohm Metal Film Resistor at R5-R8.2>.Step 2: Install 2pcs 1Kohm Metal Film Resistor at R2,R3.3>.Step 3: Install 1pcs 10Kohm Metal Film Resistor at R4.4>.Step 4: Install 1pcs 15Kohm Metal Film Resistor at R1.5>.Step 5: Install 18pcs LED at D1-D18.The longer pin is inserted into the rectangular pad(positive pole). The shorter pins are inserted into the round pads.6>.Step 6: Install 2pcs 0.1uF 104 Ceramic Capacitor at C1,C2.7>.Step 7: Install 1pcs TO-92 78L05 Voltage Regulator at U3.8>.Step 8: Install 2pcs TO-92 S8050 Transistor at Q1,Q2.9>.Step 9: Install 1pcs DIP-16 CD4017 IC at U1.There is a mark on one end of the IC and there is a mark on PCB where the IC can place on.These two marks are corresponding to each other and are used to specify the installation direction of the IC.10>.Step 10: Install 2pcs 10uF 25V Electrolytic Capacitor at C3,C4.Pay attention to distinguish between positive and negative.The Longer pin is positive pole.The longer pin is inserted into the rectangular pad. 11>.Step 11: Install 1pcs 6*6*10mm Black Button at S1.12>.Step 12: Install 1pcs TO-92 78L05 Voltage Regulator at U2.13>.Step 13: Install 1pcs 5.8*5.8mm Self-locking switch at S2.14>.Step 14: Install 1pcs 5.5mm DC Socket at J1 on another side.15>.Step 15: Install 4pcs M3*10mm and 4pcs M3*20mm Nylon Column on PCB.16>.Step 16: Install 1pcs 9V Battery socket at DC 9V. Note: Red wire connect to ‘ + ’ .17>.Step 17: Install 9V battery(not included) and then place lamp on plastic shell.Then press button to switch lamp.